Why does the floor look dry when the cabinet is wet?
Water tends to run under the appliance and into the cabinet cavity, where it wicks into the toe-kick and the base. The surface floor can look dry because the water has moved out of sight, while the cabinet and the subfloor beneath it hold most of it.
Kitchen and laundry floors are built with cabinets and appliances sitting on top of them, and the space between the floor and the cabinet base is enclosed. Water that gets into that space has nowhere to go but downward and sideways. A cabinet toe-kick can hold a surprising amount, and a swollen panel is often the first sign that the cavity has been wet for days.
The crew opens the cabinet base where the readings point and checks the subfloor beneath it. Particleboard and some plywood swell and lose strength when wet, and the damage shows up as lifting laminate or a door that no longer closes square. Measuring the cavity and the floor together gives a much clearer record than checking the surface alone.
How much of the cabinet and the flooring has to come out?
That depends on how far the water went and what the material is. Swollen toe-kicks and wet cabinet bases are often replaced, while flooring that stays firm can sometimes be dried in place. The readings decide, and the crew shows them.
Cabinet bases that have soaked up water for more than a short time usually lose their strength, and the crew notes the swelling and the readings before deciding whether to keep them. A toe-kick that has lifted from the base is a common removal, because the panel does not return to shape after it has dried. The cabinet itself is replaced by a cabinet installer, and the crew's file shows where the wetting reached.
Vinyl and laminate flooring is handled differently depending on whether it has lifted or is still flat. Flooring that is firm and bonded can be dried under the appliance space, while buckled flooring is usually lifted to reach the subfloor. Each lift is photographed, so the flooring installer knows what is underneath when the work is done.
What moves the price of an appliance leak job up or down?
How far the water traveled under the cabinets, how many cabinet bases and floor sections have to come out, whether the appliance has to be moved for access and whether the supply line is still leaking. The price is explained and approved before work starts.
The spread of the water under the cabinets is the first driver. A leak that stayed under the appliance is a different job from one that reached the toe-kick of two or three cabinets and the floor in the next room. Each cabinet and each section of flooring that has to come up is added to the file as it is found, rather than discovered at the end.
Access is the second. A built-in dishwasher that has to be pulled out of its cabinet slot, or a washer on a raised platform with a dryer stacked on top, takes time before the floor can be reached. A line still leaking when the crew arrives means the work waits on the repair. The price is explained and approved before any of that work starts.
Is an appliance hose failure covered by a homeowners policy?
North Carolina Department of Insurance consumer materials describe a sudden escape of water from inside the house as generally covered by a standard homeowners policy. That is the usual category for a hose failure, but the policy wording and the insurer decide each claim.
The department's distinction is between water that escapes from a plumbing or appliance system inside the house and water that comes in from outside, such as flood or rising water. A supply hose that splits is in the first group. A crew can state that in the file, with the location of the failed part and the date the leak was found.
The record is what matters in a claim. Photographs of the appliance and the water before anything is moved, the failed part kept if it can be, the readings from each visit and the invoice for the repair are all useful. Keep the failed hose or fitting until the insurer has seen it, and ask for any decision in writing.
Can I use the appliance again after the leak?
Not until the failed part has been repaired or replaced and the floor, cabinet base and subfloor have dried to readings. Running a repaired appliance on a floor that is still damp can start the leak again and hide it.
A washer or dishwasher that has leaked is usually checked by its own repair person, who tests the hose, the seal or the drain before it goes back into service. The restoration crew does not run the appliance to test it. It records the readings and tells the homeowner what state the floor is in, so the repair person knows whether to start.
Once the subfloor and the cabinet base read dry, the flooring and the cabinet work can follow. The crew's file goes to the installer so they know the state of the subfloor and the framing beneath. Closing the cabinet or laying the flooring early is the most common reason a second wet spot shows up later.