Phones answered 24/7Burlington, NC(833) 490-5225
Free quote (833) 490-5225
Guide

Water in a house built for the railroad and the mills

Burlington grew out of railroad shops and cotton mills, and its oldest houses hold water in odd ways. What that means when a pipe or a drain fails.

Illustration for the guide "Water in a house built for the railroad and the mills" (Burlington, NC)
Short answer

Burlington began as Company Shops, the repair yard the North Carolina Railroad established in 1855, and the neighborhoods that followed were built from the 1900s through the 1920s. Houses of that age hide their plumbing in closed chases, carry plaster rather than drywall, and dry on a different timetable from modern construction.

Key takeaways

  • The oldest Burlington neighborhoods date from the 1900s through the 1920s and, per the National Register nomination, survive largely unchanged.
  • Glencoe's mill village, built between 1880 and 1882, used heavy-timber framing with brick nogging packed into the walls.
  • Plumbing in houses of this age was added after the fact, so it runs through chases that hide a leak rather than reveal it.
  • Wet plaster and wet drywall behave differently; plaster can often be saved, and the lath behind it is the part that holds water.
  • Original wood floors cup and crown as they take up and release moisture, and the direction tells you what stage the drying is at.
  • Drying an old house well means opening as little as possible, which takes more measurement rather than less.

What kind of housing stock is this guide about?

Two overlapping groups: the privately built city neighborhoods of the 1900s through the 1920s, and the mill villages built beside the factories that gave the county its industry. Both are older than modern plumbing conventions.

The National Register nomination for the city records that many of those privately built neighborhoods, centered on Davis and Mebane streets, are little changed from when they went up. That is a preservation observation, and it is also a plumbing observation: a house that has not been substantially rebuilt has not had its original pipe runs rationalized either.

The mill villages are a distinct type. Glencoe Cotton Mill and its village were built for the Holt family between 1880 and 1882 on a hundred and five acres, and the property became a National Register district before Preservation North Carolina bought it in 1997. About half the mill's workers lived beside the works, in houses built to a repeating pattern.

What does heavy-timber framing with brick nogging mean for water?

It means the wall is dense and slow. Brick nogging packed between timbers stores moisture and gives it up gradually, so a wall that has taken water stays measurably wet long after a comparable modern stud wall has dried.

Dense assemblies are a mixed blessing in a flood. They resist damage better than a hollow stud bay filled with fiberglass, because there is no batt to lose its function and no cavity for water to pool in. But they also act as a reservoir, releasing moisture into the room for weeks and keeping adjacent wood and finishes damp while they do it.

The practical consequence is patience and measurement. A crew cannot read the inside of a nogged wall the way it reads a stud cavity through a small opening, so it takes surface and penetrating readings in a grid and watches the trend. Our mill village house water damage page describes that approach.

What about the mill buildings themselves?

They are a different scale of the same problem. Large masonry and heavy-timber structures, many of them beside the river, hold water in thick walls and timber floors and take correspondingly longer to bring back to a dry reading.

The county's industrial record runs from Saxapahaw, where the first mill went up in 1844 under the Quaker settler John Newlin and a spinning mill operated into the twentieth century before closing in 1994, through to the Glencoe works on the Haw. Buildings of that kind have since been converted to other uses, which puts modern finishes and services inside a nineteenth-century shell.

A water event in one of them is handled as a commercial job with a preservation problem attached. Volumes are large, so the equipment count is high; timber floors and masonry walls dry slowly, so the schedule is long; and the occupants usually cannot simply close. The commercial and mill building page sets out how that is planned.

Why do supply lines in these houses fail where they do?

Because they were retrofitted. Water was brought into houses built without it, so pipes follow whatever route was available: through closets, up the backs of chimneys, along joists in an unheated crawl space and inside walls that were never meant to be opened.

Those routes concentrate failures in the least convenient places. A line running through an unheated or poorly sealed crawl space is exposed to cold in a way an interior line is not. A line in an exterior wall of a house with little insulation is exposed in the same way. When a freeze does split a line, the water is released inside a closed assembly.

Age compounds it. Decades of different repairs leave a building with several generations of pipe and fitting in one system, and the failure usually happens at a transition between them. Our burst pipe water damage page covers what happens next, and the hidden leak detection page covers finding the slow version.

How does plaster behave when it gets wet?

Differently from drywall, and usually better. Lime and gypsum plaster on wood lath can absorb a wetting and recover, where a paper-faced gypsum board of the same dimensions would be ruined. The lath behind it is the part that matters.

Wood lath holds water in its grain and in the keys of plaster pushed between the strips. A plaster wall can therefore feel dry on the face while the assembly behind it still reads high, and a crew that tests only the surface will call the job finished too early. The failure mode to watch for is not crumbling but a slow separation of plaster from lath.

Keeping original plaster is usually worth the extra drying days, both for the building and for the owner. It takes directed airflow across the surface and a dehumidifier holding the room low enough that the wall gives up moisture instead of equilibrating with damp air. Pressure and patience, rather than demolition, is the method that works.

What happens to original wood floors?

They move. Boards take up water from below or from a spill, swell across the grain and cup, then crown as they dry if the drying is uneven. The movement is often recoverable if nobody sands or refinishes while the wood is still wet.

Cupping means the edges of each board are higher than the center, which is the signature of moisture arriving from underneath. Crowning is the reverse and often means the surface dried faster than the underside, sometimes because somebody put heat on it. Reading which is happening tells a crew where the water is and whether the drying plan is balanced.

The temptation to repair early is the main enemy of an old floor. Wood that is sanded flat while swollen will be left dished when it finishes drying, and a finish applied over damp boards traps the moisture underneath. The right order is dry, wait, measure, and only then decide whether anything needs doing at all.

Where does water hide in a house of this age?

In closed chases, behind baseboards and under stair landings, in the voids beside a chimney, under layers of flooring added over the decades, and in the crawl space where the whole system passes through on its way to the fixtures.

Layered flooring is the one people miss. Many of these houses have had sheet goods laid over the original boards and then another covering laid over that, which produces a sandwich that traps water between layers and reads dry at the surface. A meter reading taken on top of three layers tells you about the top one.

Chases and voids are the other reservoir. Pipe runs boxed in during a long-ago renovation are closed assemblies with no ventilation, and water released inside one stays there. These are the places a technician probes with a thermal camera and a penetrating meter rather than guessing, because the alternative is opening finishes that cannot be replaced.

What does a failing drain of this vintage look like?

A recurring slow backup, a smell that comes and goes, or a damp patch that reappears after heavy use rather than during it. Old clay and cast components crack and shift, and the leak follows use instead of running continuously.

Intermittency is what makes these hard to pin down. A leak that only wets a cavity when the upstairs bath drains can soak a joist bay for months without ever producing a visible puddle, and the first evidence may be a ceiling stain or a soft spot in a floor some distance from the fixture.

Because the water is not clean, the response differs from a supply leak. Soft material in the wet area is removed rather than dried, surfaces are cleaned, and the pipe itself goes to a plumber. The restoration side handles the building; the sewage backup cleanup page explains how contaminated water changes the method.

How is drying handled when the finishes cannot be replaced?

By measuring far more and cutting far less. Access is taken where it will not show, airflow is directed into cavities through small controlled openings, and the dehumidification does the work that demolition would do in a newer house.

Small holes in an inconspicuous place, drying mats on a floor and pressure differentials that pull air through a cavity all achieve what a flood cut achieves, without removing material that cannot be matched. It is slower and needs more visits, and it is the right trade when the finish is a hundred years old and irreplaceable.

That approach depends entirely on the readings being trusted. A crew working this way has to be able to show you the numbers falling week by week, because there is no visible open wall to inspect. Ask for the log, and ask what the target number is for each material before the equipment goes in.

Frequently asked questions

Does an older house dry faster or slower than a new one?

Slower, as a rule. Dense assemblies such as plaster on lath and timber walls packed with brick nogging store moisture and release it gradually, where a modern stud wall with batt insulation either dries quickly or has its wet material removed. The compensation is that less of an old house usually has to be thrown away.

Should original plaster be torn out after a flood?

Not automatically. Plaster on wood lath often survives a wetting that would destroy gypsum board, and the decision should follow readings taken in the assembly rather than at the surface. Where it has separated from the lath or lost its keys it has to go, but that is a specific finding, not a default.

The water bill went up but I cannot see a leak. What now?

In a house of this age that is the most common way a leak announces itself, because the pipe is inside a closed chase or under a crawl space. Shut every fixture and watch the meter; if it still moves, the search is for a hidden line. That is a detection step before any drying is scoped.

Is a crawl space under one of these houses a separate problem?

It is the same water seen from below, and it is often where the evidence is clearest. Wet insulation, damp ductwork and standing water under the floor all keep a house humid long after the rooms look fine. The guide on crawl space moisture deals with it in full.

Who should I call first about an old house?

Call the line on (833) 490-5225 for the water itself, at any hour, and keep the building trades separate. A plumber repairs the pipe, a roofer the roof, and the restoration crew takes the water out and dries the structure. Say on the call that the house is of this period, because it changes the equipment that is sent.

Sources

  1. National Park Service, National Register documentation (NPGallery)
  2. Wikipedia: Burlington, North Carolina
  3. Wikipedia: Saxapahaw, North Carolina

This guide is general information for Alamance County homeowners, not a substitute for an on-site inspection. Prices are estimates. See our disclaimer.

Need help today?

Call any hour and explain what is going on. You get a clear price before any work starts.

Keep reading

More guides

What decides the size of a water cleanup quote in Burlington

The size of a water damage scope in Burlington follows four measurable things: how much floor area got wet, how far moisture climbed into walls and framing, how many days it sat there, and whether the water was clean supply water or came off the ground.

WhatsApp